2007 Toyota FJ Cruiser: El Froggo

[Frogeye]

Bring on the Mish Mash: ARMOR

Lucrum Winch Mount and Light Bar


ALL PRO IFS Skid Plate


ALL PRO Automatic Transmission Skid


ALL PRO Transfer Case Skid (Thank you Bobo)


ALL PRO Rear Axle Skid (Thank you Ruebarb)


ALL PRO Rock Rails


O&B Fab Rear Lower Control Arm Upgrade and Skid (version1)


ALL PRO Rear Shock Skids


O&B Fab Sway Bar Clamps (version1a) Why you should clamp it? Your stock sway bar will shift under extreme conditions. Basically, everytime you go off road. When your sway bar shifts, it knocks into your coil overs and can either bend the sway bar link or break it. If you break a sway bar link you are going to rip a CV boot for sure and that's expensive if you don't work on the rig yourself. Put on a set of good clamps, and your sway bar will not move anymore. Piece of mind for sure.


A good set of Shock boots to protect my Rear Walker Evans. Thank you BellyDoc


ALL PRO E Locker Skid

[OLLIE]

I saw Frogeye's rig one time... It's quite a machine.

[Frogeye]

Where's the edit button?

[DaveK]

Very nice. Looks like you replaced the factory skid plate? Who makes it and how does it hold up?

[Brucek]

Very very nice, but don't you find it hard finding your way around after dark?

[OLLIE]

Very nice. Looks like you replaced the factory skid plate? Who makes it and how does it hold up?

That is made by All-Pro... If you can't find good skids for your Hummr I might know someone who sould fabricate them for you... If it can handle the additional weight.

[DaveK]

Very nice. Looks like you replaced the factory skid plate? Who makes it and how does it hold up?

That is made by All-Pro... If you can't find good skids for your Hummer I might know someone who sould fabricate them for you... If it can handle the additional weight.

Thanks for the lead, but I installed the rubber duck UCP a couple years ago. Virtually the same as the H1's and (so far) quite durable. While this photo does not show it, the UCP covers everything from the front to past the t-case. The weight will be no problem as soon as I get one of those FJ's out of my glove box.

[Frogeye]

SUSPENSION AND TIRES

Front and Rear Walker Evans Suspension (fully adjustable)



2 inch DR Racing Rear Coil Springs (Thank you forum member who sold them to me)

Extra long Rear Steel Braided Brake Lines (Thank you Cruiser Larry at Dirty Parts)

ProComp All Terrain 265 70 17s on Stock Alloys







ALL PRO Ultimate Front Sway Bar Links

Note that I've added a conical spacer at the top and the bottom where the link mounts to spindle and the sway bar. (Thank You Thong buddy for helping me out.)

[Frogeye]

RECOVERY

Lucrum Winch Mount with a Mile Marker MX8


Snatch Block, Straps, D Shackles, HighLift jack, Shovel

ENGINE PERFORMANCE

TRD Drop-In Air Filter



Custom bashed Up Rear Exhaust Pipe

LIGHTING

3 135 Watt PIAA 580xt Xtreme White Driving Lamps

2 55 Watt Hella 500 Fog Lights



Four programable flashing LEDs in the back for use in limited visibility situations







Six 55 Watt Rock Lights

[Frogeye]

ELECTRONICS

Scanguage II (Thank You Cruiser Larry)



Yaseu VX6R HT Dual Band Radio



YAESU - FT-8800R 144/430 MHz Dual Band FM Transceiver. I picked up a $30.00 Radio Shack mini external speaker that I use with the 8800



Power Inverter In The Front For The Laptop

2 12 Volt Accessory Plugs In Center Console



Radio Shack CB

3’ Fire Fly Stick CB Antenna

Bandi CB Mount

Mag Mount Dual Band Antenna

PainLess Dual Battery Kit and a Blue Torch Fab Battery Box holding an Optima Yellow Top. Huge thank you to FJ-Ollie for helping me instal the dual battery kit the battery box, and the Mile Marker MX8 Winch.









SAFETY

Basic Bug Out survival kit

TOOLS & TRAIL EQUIPMENT

Basic load out of tools when on the trail to do most trail fixes. I also carry a complete spare axle shaft when wheeling. If not for me for someone else.

ADDITIONS

Atrac Hack

Kill Switch

Stock Roof Rack (Thank you Air2Air, and thank you FJ-Ollie for the aluminum mesh floor for the rack)



Steel Mesh BBQ Grill Lens Covers, Ellis Precision CNC Billet Aluminum Ouray 2007
Badge, White BezeL



Ellis Precision CNC Billet Aluminum Battery Clamp



Stant Locking Gas Cap

Homemade Laptop Mount “Killer Laptop” holding my Dell 600 running DeLorme Topo USA



Homemade Rear Door Speaker Mounts

CUSTOM EXTERIOR MOD’s

Blacked Out My Stock Alloys



4 Wheel Drive Emblem



Lucrum Winch Mount, light bar, and Bumper Wing Eliminators (Thank You Chris)



Cleghorned my Right Rear Quarter Panel